Silicone Vacuum Hose

Hose by Foot

HOSE by the foot -- United States only!

Silicone Vacuum Hose, Cloth Covered, Fuel Line, Hose Cutter Great for do it yourself.

Our vacuum hose has thick walls that can withstand high pressure, make tight bends without collapsing, and has an airtight fit. When sized correctly our vacuum hoses do not require clamps or zip ties, even when on the pressure side of a forced induction system. Vacuum hose should have an airtight fit on the nipple it connects. Never use silicone hose for fuel, oil, or any petroleum base products.

Hose Comparison -- Our left (blue). Our competitors right (red). SAME DIAMETER! Hose Colors -- Red, Green, Yellow, Silver/Gray, Purple, Black, Blue.

For a video of our hose holding 50 pounds of boost with no clamps, go here: http://www.youtube.com/watch?v=TdbKRUYPhyE

For a video of an oem and a competitor's hose not holding boost, go here: http://www.youtube.com/watch?v=QQsgVkrlwpc

For a video of a comparison of our silicone hose at high tempatures vs our competitor http://www.youtube.com/watch?v=1fjRYS9ytww

Silicone Vacuum Hose United States only. Minimums apply.

Part #

Size Range I.D. (inches)

Size I.D. (mm)

Minimum

US & Territories only

Buy

Price per foot

Vacuum

V475

1/8

10 ft

1.20

Vacuum

V492

5/32

10 ft

1.25

Vacuum

V476

1/4

10 ft

2.05

Vacuum

V493

5/16

10 ft

2.85

Vacuum

V477

3/8

5 ft

3.10

Vacuum

V488

15/32

2 ft

6.02

Vacuum

V489

5/8

2 ft

7.37

Vacuum

V490

3/4

2 ft

10.61

Vacuum

V491

25.4

2 ft

16.92

Note: Hose sizes are listed in inner diameters. We don't list a 1/2" size because the 15/32" (12mm) hose fits this size perfectly. For a really tight fit you can use 10mm hose on a 1/2" fitting. We normally suggest using hose one or two sizes smaller than the fitting to insure a very tight fit. Call if you have any questions about this. Our hose can stretch to fit really large fittings without splitting. For example our 10mm hose can be forced onto a 16mm fitting!

International orders must email for shipping quote. Order other than US & Territories will be refunded. misty@hiperformancestore.com

Cloth Covered email or call for quote/availability 918-760-0668 misty@hiperformancestore.com

This cloth covered hose is designed for high pressure transmission of oil, gas, air, water, coolants, etc. where operating pressures do not exceed 300 psi. Oil and mildew resistant textile black braid. Temperature range: -40°F to +250°F (-40°C to +121°C). Great to replace factory hoses that are cracking. Use in places you cannot use silicone.

Type	Part number	Size ID (Inches)	Size mm	Minimum	Price per foot
Cloth Covered	GA250	1/4 inch ID	6 mm	1 foot	3.92
Cloth Covered	GA357	3/8 inch ID	10 mm	1 foot	4.18
Cloth Covered	GA500	1/2 inch ID	12 mm	1 foot	4.80
Cloth Covered	GA625	5/8 inch ID	16 mm	1 foot	5.60
Cloth Covered	GA750	3/4 inch ID	19 mm	1 foot	7.38

International orders must email for a shipping quote.

Fuel Injection Hose (hi pressure) 100 psi email or call for quote/availability 918-760-0668 misty@hiperformancestore.com

Our fuel injection hose is designed to safely and efficiently handle the higher pressure, tempatures, and chemical problems inherent in today's hotter running, fuel injected engines. Can be used with oxygenated gas plus methanol and ethanol additives. Suitable for diesel and bio-diesel fuel. Abrasion-resistant outer cover resist temperature extremes of -30°F to +300°F (-34.5°C to +149°C) as well as oil, grease, ozone, and coolants. Meets SAE and CARB requirements. Working pressure of 100psi with burst strenght of 900psi. Use for fuel.

Type	Part number	Size ID (Inches)	Size mm	Minimum	Price per foot
Fuel Injection	F250	1/4 inch	6 mm	1 foot	6.30
Fuel Injection	F312	5/16 inch	8 mm	1 foot	6.54
Fuel Injection	F375	3/8 inch	10 mm	1 foot	8.01

Fuel Hose (low pressure) 35 psi to 50 psi email or call for quote/availability 918-760-0668 misty@hiperformancestore.com

Designed for use on all types of gasoline engines, except those with fuel injection...see fuel injection hose. Excellent resistance to oil, gasoline, greas, and weather. It is constructed with a neoprene cover and nitril tube for use with leaded and unleaded gasoline, gasohol, and diesel fuels, reinforced with a single ply of braided cored. Meet SAE requirements. Max working pressure 50 psi for ID sizes 1/4, 5/16, 3/8. Max working pressure 35 psi for 1/2", 5/8, and 3/4 inch h Not suitable for bio-diesel fuel.

Type	Part number	Size ID (Inches)	Size mm	Minimum	Max working pressure psi	Price per foot
Fuel Low Pressure	FLP250	1/4 inch	6 mm	5 foot	50 psi	2.03
Fuel Low Pressure	FLP312	5/16 inch	8 mm	5 foot	50 psi	1.47
Fuel Low Pressure	FLP375	3/8 inch	10 mm	5 foot	50 psi	2.18
Fuel Low Pressure	FLP437	7/16 inch	11mm	5 foot	35 psi	1.53
Fuel Low Pressure	FLP500	1/2 inch	12 mm	5 foot	35 psi	1.47
Fuel Low Pressure	FLP625	5/8 inch	16mm	5 foot	35 psi	2.67

Heavy Duty Hose Cutter

Hose Cutter

$29.95

We stock a large selection of silicone and other types of hose in various sizes. If we don't have a specific hose kit for your car, we can almost certainly provide replacement hoses from our supply. If you need hose by the foot contact us with your needs.

Shipping via USPS priority mail.

Returns

Refunds will be issued less a 15% restocking fee once item(s) are received. We do not refund shipping fees.

Silicone vacuum hoses and couplers have an 18 month guarantee against failure, but should last the life of your car.

All returns must be made within 30 days, and the item must be in a "New in Box" condition.

Cloth covered hose, fuel injection hose, and heater hose (less than 10 feet in length) are not returnable. It would be impossible for us to resale a piece that we cut to size for you.

[ Home ]